Layout and commands derived from the behaviour of its control software, tested against the simulator only. No GEQ on this model; dynamic EQs are left untouched. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
11 KiB
t.racks DSP 204 / DSP 408 – control protocol
Documented for interoperability by observing the communication between the devices and their control software
and by testing on real devices. Both models speak the same protocol; only the number of channels and the size
of the memory image differ. Implementation: dsp/protocol.py.
Status: the network transport and all commands below are implemented and tested against the simulator; links, the limiter status bits and USB were verified on a real DSP 204 (firmware V0104P). Points marked assumed are not verified yet.
Transport
- Network: TCP, port 9761. Factory default IP
192.168.1.101. - USB: HID class device, no driver needed, VID 0x0168 / PID 0x0821 (both models). See USB.
- Request/response: send one command and wait for its answer before sending the next.
- The DSP accepts only one connection at a time.
Frame
10 02 SRC DST LEN CMD PAYLOAD… 10 03 CHK
| Field | Meaning |
|---|---|
| SRC/DST | PC→DSP: 00 01, DSP→PC: 01 00 (01 = device ID) |
| LEN | 1 + len(PAYLOAD) (includes CMD) |
| CHK | XOR from 02 to 03, i.e. 0x01 ^ SRC ^ DST ^ LEN ^ CMD ^ PAYLOAD… |
There is no byte stuffing – a payload may contain 10 03, so always parse by LEN.
All 16-bit words are little endian.
Read / system commands
| CMD | Direction | Payload | Meaning |
|---|---|---|---|
10 |
→ | – | Handshake |
13 |
→ / ← | – / ASCII | Device info, answer starts with DSP204 or DSP408 |
2C |
→ / ← | – / [time lock][4 bytes][device lock] |
Lock state, see Device lock |
22, 14 |
→ | – | Init queries (sent during connect, content unknown) |
29 |
→ / ← | [idx] / [idx][name…] |
Preset name (idx 0-based) |
20 |
→ | [idx+1] |
Recall preset |
26 |
→ | name[14] |
Set name for the next store |
21 |
→ | [idx+1] |
Store current state into preset |
27 |
→ | [chunk] |
Request config chunk |
24 |
← | [chunk][50 bytes] |
Config chunk; 204: chunks 0…14, 408: 0…28 |
12 |
→ | – | Status (sent after the dump) |
2D |
→ / ← | [0][code 4] / [0][result] |
Unlock with the lock code, result 1 = unlocked, 0 = wrong code |
2F |
→ | [code 4] |
Set a new lock code |
11 |
→ | – | Sent after setting a lock code (meaning not fully known) |
40 |
→ / ← | – / meters | Read levels (also serves as keepalive) |
Meter answer
12 entries × 3 bytes b0 b1 b2, followed by 2 status bytes.
- Level = float32 from the bytes
00 b2 b0 b1(little endian) → linear, dB = 20·log10. - Positions: 0–3 = In A–D, 4–11 = Out 1–8. The 204 uses 0, 1 and 4–7.
- The level is measured before mute.
- Limiter active: the status bytes are a bit mask of the outputs (bit 0 = Out 1). Measured on a DSP 204:
00 03while Out 1+2 limit,00 0Cfor Out 3+4. That Out 5–8 of the 408 continue in the same 16-bit value is assumed.
Channel numbers
| Device | Inputs | Outputs |
|---|---|---|
| DSP 204 | In A=0, In B=1 | Out 1–4 = 2–5 |
| DSP 408 | In A–D = 0–3 | Out 1–8 = 4–11 |
Set commands
| CMD | Parameter | Payload |
|---|---|---|
34 |
Gain | [ch][u16 gain] |
35 |
Mute | [ch][0/1] |
36 |
Polarity | [ch][0/1] |
38 |
Delay | [ch][u16 delay] |
32 |
High pass (low cut) | [ch][u16 freq][slope] |
31 |
Low pass (high cut) | [ch][u16 freq][slope] |
33 |
PEQ band | [ch][band][u16 gain][u16 freq][q][type][bypass] |
48 |
GEQ band (inputs) | [ch][band 0–30][u16 gain] |
3E |
Gate (inputs) | [ch][attack][release][hold][threshold] (u16 each) |
30 |
Compressor (outputs) | [ch][ratio][attack][release][knee][threshold] |
3F |
Limiter (outputs) | [ch][attack][release][knee][threshold] |
3A |
Routing matrix (outputs) | [ch][bit mask of inputs] |
41 |
Mix level (outputs) | [ch][input][u16 level] |
3D |
Channel name | [ch][name 8] (printable ASCII) |
3B |
Link | [ch][u16 link mask] (see Channel links) |
3C |
PEQ bypass | [ch][0/1] – all PEQ bands of the channel bypassed |
49 |
GEQ bypass (inputs) | [ch][0/1] |
39 |
Test signal | [source][freq] – source 0 = analog inputs, 1 = pink noise, 2 = white noise, 3 = sine; freq = index 0–30 of the 1/3-octave frequencies 20 Hz…20 kHz (as the GEQ) |
15 |
Delay unit | [unit] (display only) |
The format of the acknowledgement the DSP sends after a set command is not fully understood yet.
Value encoding
| Parameter | Raw | Conversion |
|---|---|---|
| Gain / mix level | 0–400 (mix 0–280) | r<80: r/2−60 dB, else (r−280)/10 dB → −60…+12 dB |
| Frequency (PEQ, HP, LP) | 0–300 | 1000 · 2^((r−170)/30) Hz → 19.7 Hz…20.16 kHz (1/30 octave) |
| PEQ/GEQ gain | 0–240 | (r−120)/10 dB → ±12 dB |
| Q | 0–100 | table 0.4…128 (see protocol.py) |
| PEQ type | 0–8 | Peak, Low shelf, High shelf, HPF −6, HPF −12, LPF −6, LPF −12, Allpass 1, Allpass 2 |
| Slope | 0–20 | 0 = bypass, 1–20 = BW−6, BL−6, BW−12, BL−12, LK−12, … LK−48 |
| Delay | 0–65280 | r/96 ms (max 680 ms) |
| Threshold (gate/comp/limit) | 0–220 | (r−180)/2 dB (gate max 0 dB, comp/limit max +20 dB) |
| Attack | 0–998 | r+1 ms |
| Release | 9–2999 | r+1 ms |
| Hold | 9–998 | r+1 ms |
| Ratio | 0–15 | 1.0, 1.1, 1.3, 1.5, 1.7, 2.0, 2.5, 3.0, 3.5, 4.0, 5.0, 6.0, 8.0, 10, 20, Limit |
| Knee | 0–12 | dB |
The absolute output level that corresponds to 0 dB limiter threshold is not published; the app assumes 0 dBu.
Channel links
Measured on a DSP 204 (firmware V0104P). Every channel has a u16 mask (bit = channel index within the inputs or within the outputs):
| Channel | Mask |
|---|---|
| not linked | its own bit only (Out 3 = 04) |
| first channel of a group | bits of all members (Out 3+4 = 0C) |
| further members | 00 |
- Set with
3B [ch][mask]– for every channel of the group (first channel first). - When a group is formed, the DSP copies the settings of the first channel to the others.
- The DSP itself applies every change on a member to the whole group (gain, delay, polarity, HP/LP, PEQ, GEQ, gate, compressor, limiter, mute) – but not channel name, routing matrix and mix levels.
- A member with mask
00that is not part of a group ignores changes: when unlinking, give every channel its own bit again.
Device lock
The DSP can be protected with a 4-character code (digits and upper-case letters, e.g. A1BA, sent as ASCII).
- During connect, the answer to
2Creports the lock state: byte 5 ≠ 0 means the device is locked. Byte 0 and bytes 1–4 belong to a separate time-based lock that this app does not use. - A locked device waits for
2D [00][code]before the rest of the initialisation (22,14, preset names, dump). The answer2D [00][01]means unlocked,2D [00][00]wrong code. 2F [code]stores a new code; the control software sends11afterwards. The device asks for the new code from the next connection on. A command to remove the lock is not known.
Status: derived from the behaviour of the control software and implemented against the simulator; not yet verified on a real device.
Config dump = memory image
Chunk n carries bytes n·50 … n·50+49 of the device memory image.
0x00 u8[2] ?
0x02 char[14] preset name
0x10 Input[nIn] 140 bytes each
+0 name[8]
+8 gate: attack, release, hold, threshold (4×u16)
+16 geq[31] u16
+78 peq[8] {u16 gain, u16 freq, u8 q, u8 type}
+126 u16 hp_freq, u16 lp_freq, u8 hp_slope, u8 lp_slope
+132 u16 gain, u16 polarity, u16 delay, u16 link mask
Output[nOut] 96 + 2·nIn bytes each
+0 name[8]
+8 u16 matrix bit mask
+10 u16 mix[nIn]
… u16 hp_freq, u16 lp_freq, u8 hp_slope, u8 lp_slope
… peq[9] {u16 gain, u16 freq, u8 q, u8 type}
… comp: ratio, attack, release, knee, threshold (5×u16)
… limit: attack, release, knee, threshold (4×u16)
… u16 gain, u16 polarity, u16 delay, u16 link mask
u16 input mute bit mask, u16 output mute bit mask
u16[nIn + nOut] unknown
u16 test signal source, u16 test signal frequency index (see command 39)
u16 unknown
u16 PEQ bypass bit mask inputs, u16 PEQ bypass bit mask outputs (command 3C)
u16 GEQ bypass bit mask inputs (command 49)
Total size: DSP 204 = 724 bytes (15 chunks), DSP 408 = 1448 bytes (29 chunks). Where the PEQ bypass flag is stored in the image is not known yet.
USB (HID)
- Both models: VID 0x0168, PID 0x0821, HID class, no driver.
- Send: report ID
00+ one complete frame (10 02 … 10 03 CHK), zero-padded to the output report length. - Receive: every input report holds exactly one frame starting at byte 0, length =
LEN + 8, then padding. - The frames are identical to TCP; the longest (config chunk, 50 data bytes) is 60 bytes and fits a 64-byte report.
FIR DSP 408 (unverified)
Derived from the behaviour of its control software, not yet seen on a device. Same frames; device info starts with
FIR408. The memory image has 1573 bytes (32 chunks) and its own layout:
| Offset | Content |
|---|---|
0x010 + 138·n |
Input: name 8, gate 4×u16, 3 dynamic EQs of 16 bytes, 8 PEQ bands of 6 bytes, compressor (ratio, attack, release, knee, threshold, EQ frequency as u16, 2 bytes), FIR taps u16, FIR bypass u16, gain, polarity, delay, link |
0x238 + 108·n |
Output: name 8, matrix u16, mix 4×u16, u16, HP frequency u16, LP frequency u16, HP slope, LP slope, HP bypass, LP bypass (bytes), FIR type, window (bytes), low Hz, high Hz, taps index (u16), 9 PEQ bands, limiter (ratio, attack, release, knee, threshold), gain, polarity, delay, link |
0x598 |
Mute masks: inputs u16, outputs u16 |
0x59C |
Bypassed PEQ bands, u16 bit mask per channel (inputs, then outputs) |
0x5B4 |
FIR name per channel, 8 characters each |
No GEQ on this model, no master bypass commands. Slope index without the "bypass" entry (0 = BW -6). Changed commands:
| Cmd | Payload |
|---|---|
0x31 / 0x32 |
[ch][u16 freq][slope][1 = bypass] |
0x30 |
[ch] ratio, attack, release, knee, threshold, EQ frequency as u16, [EQ type][EQ bypass] (inputs) |
0x3F |
[ch] ratio, attack, release, knee, threshold as u16 |
0x4B |
[ch][type][window][u16 low Hz][u16 high Hz][u16 taps index], outputs. Type: bypass, low, high, band, external. Window: rectangle, Bartlett, Hanning, Hamming, Blackman, sine, sinc, Nuttall, Kaiser, Blackman-Nuttall, Blackman-Harris. Taps = 256 + 32·index |
0x4E |
[ch][packet][u16 total] + up to 12 floats, most significant byte first |
0x4F |
[ch][1 = bypass], inputs |
0x5B |
[ch] + 8 characters of FIR name |
At most 2048 coefficients per input, 1024 per output, 4096 over all channels.